Frustrated Newbie - Help with Nodes and Sensors

Emenike

Please note that I am using a Nano for my gate way...
I thought the baud rate should be the same for Arduino and the Putty sniffer, I will revert to "38400"...

Tag

@emenike

Make sure that the same baudrate is used in the gateway sketch and mycontroller.....

Emenike

@tag
but that was exactly how it was until you said to change 38400 …. but it connected alright after | changed to 38400 and brought the node next to the laptop.

skywatch

@emenike said in Frustrated Newbie - Help with Nodes and Sensors:

@skywatch Thanks @skywatch

Please note that I am using a Nano for my gate way...
I thought the baud rate should be the same for Arduino and the Putty sniffer, I will revert to "38400"...

That part of the gateway sketch is an 'If' statement. It just tells the compilier that 'if' the board is a 3.3v 8MHz type, then reduce the baud rate to match. 8MHz boards are not reliable at 115200.

Tag

@emenike

Okay so if I understand correctly, all works if the nodes are basically next to each other... is that correct?

Emenike

@tag Yes! All works well when they are next to each other on the same desk.
I have reverted the default baud rate and all is well. I have gone ahead to create Triggers and Conditions, Schedules, Actions, etc. But I somehow can not seem to tie all up to do what I want.

I want to do a whole lot of things, but lets start with the first one. I need to pull in time and date from the controller to my node. How do I do this? Can I have a simple example that shows the steps or syntax and I will try to do other stuff. The Mysensors node uses a project that pulls data from Weather Underground, which I learnt has stopped its free weather information services. I have researched the topic and found a likely alternative in Open Weather Service) . Is anyone using Open Weather? https://openweathermap.org/current)

I need to create Actions (or triggers that target all 8 objects from my node and set them all "on".
I need to create another action trigger that targets all 8 objects and sets them to "off"
I need to create an action trigger cycles through each value on the node and turn them on for a duration I have a variable in the Controller on each value to determine how long each one will run. Its a whole lot, and it appears I may have bitten off more than I can chew.

jkandasa

@emenike

To receive time in your node, you have to call requestTime(); from your node, then you will receive time on the following function(add this in your node code),

void receiveTime(unsigned long _timestamp){
   // do actions with received time
}

Regards Wunderground: I have added details in https://forum.mycontroller.org/topic/215/weatherdata-structure-question/3 looks like they will give some access for personal use.
Regards Open weather, we do not have any direct support, however, you may use a script to collect data.

I need to create Actions (or triggers that target all 8 objects from my node and set them all "on".

You need to create 8 Operations for each object. Send payload operation with 1(ON), Add all of them in a rule. define your condition in the rule.

I need to create another action trigger that targets all 8 objects and sets them to "off"

You need to create 8 Operations for each object. Send payload operation with 0(OFF), Add all of them in a rule. define your condition in the rule.

I need to create an action trigger cycles through each value on the node and turn them on for a duration I have a variable in the Controller on each value to determine how long each one will run. Its a whole lot, and it appears I may have bitten off more than I can chew.

Seems this is complex, we may not easy by simple rule definition/timer. A script will be a good solution for this.

Some of the discussions,
https://forum.mycontroller.org/topic/45/timers-and-scripts
https://forum.mycontroller.org/topic/262/how-to-automatically-turn-off-relay-after-defined-time

Emenike

Thanks @jkandasa you are awesome support. I see the requestTime() function call in the sketch, but where in MyController do I add the node code?

void receiveTime(unsigned long _timestamp){
   // do actions with received time
}

Emenike

I have created the UID Tags... See below, did I do it right? UID Tags.png

I then tried to create the JS script as described in your old reference you supplied... but I got an error.

RunQuery Error.png

What are I doing wrong?

jkandasa

@Emenike

I see the requestTime() function call in the sketch, but where in MyController do I add the node code?

This code needs to be added to your MySensors node sketch, the example in your sprinkler sketch.
Nothing to do with MyController to receive timestamp.

jkandasa

@Emenike said in Frustrated Newbie - Help with Nodes and Sensors:

I then tried to create the JS script as described in your old reference you supplied... but I got an error.

Did you modify the script? If yes, can you post your script?

If not, you have to create all the UID, valve-status is not available in your UID's list also Value 1 is different then value01

Emenike

Hello @jkandasa
I have been out of town, haven't touched MYC for a while. Just popped intoday and tried my hands on the script. Ran it after creating the Operation and the Timmer to trigger and run it. But it wont tun. I get an error ```

{
  "errorMessage": "TypeError: Cannot get property \"status\" of null in <eval> at line number 8"
}

Here is the JS script that I edited for 8 valves

var myImports = new JavaImporter(java.io, java.lang, java.util);

with(myImports) {
  
  var LoopThroughValves = mcApi.variable().get("Status");

  //Check already running?
  if(LoopThroughValves.status !== 'running'){

    //Update as running
    valveStatus.value = "running";
    mcApi.variable().update(valveStatus);
    mcApi.logger().debug("Loop Through Valve Script Triggered...");
    
    var masterValve = mcApi.uidTag(0).getByUid("All Zones").getResource();
    var valve01 = mcApi.uidTag().getByUid("Zone 1").getResource();
    var valve02 = mcApi.uidTag().getByUid("Zone 2").getResource();
    var valve03 = mcApi.uidTag().getByUid("Zone 3").getResource();
    var valve04 = mcApi.uidTag().getByUid("Zone 4").getResource();
    var valve05 = mcApi.uidTag().getByUid("Zone 5").getResource();
    var valve06 = mcApi.uidTag().getByUid("Zone 6").getResource();
    var valve07 = mcApi.uidTag().getByUid("Zone 7").getResource();
    var valve08 = mcApi.uidTag().getByUid("Zone 8").getResource();

    var delayTime = 1000 * 60 * 10; //10 minutes
  
    //Turn ON master valve and Valve01
    masterValve.value = "1"; //Update master valve ON state
    mcApi.sensor().sendPayload(masterValve); //sensd state
    valve01.value = "1"; //Update valve01 ON state
    mcApi.sensor().sendPayload(valve01); //sensd state
      
    //Update valve01 is running
    valveStatus.value2 = "value01";
    mcApi.variable().update(valveStatus);
    //Wait time
    Thread.sleep(delayTime);
  
    //Turn OFF valve01 and turn ON valve02
    valve01.value = "0"; //Update valve01 OFF state
    mcApi.sensor().sendPayload(valve01); //send state
    valve02.value = "1"; //Update valve02 ON state
    mcApi.sensor().sendPayload(valve02); //send state
    
    //Update valve02 is running
    valveStatus.value2 = "value02";
    mcApi.variable().update(valveStatus);
    
    //Wait time
    Thread.sleep(delayTime);
  
    //Turn OFF valve02 and turn ON valve03
    valve02.value = "0"; //Update valve02 OFF state
    mcApi.sensor().sendPayload(valve02); //send state
    valve03.value = "1"; //Update valve03 ON state
    mcApi.sensor().sendPayload(valve03); //send state
  
    //Update valve03 is running
    valveStatus.value2 = "value03";
    mcApi.variable().update(valveStatus);
  
    //Wait time
    Thread.sleep(delayTime);
  
    //Turn OFF valve03 and turn ON valve04
    valve03.value = "0"; //Update valve03 OFF state
    mcApi.sensor().sendPayload(valve03); //send state
    valve04.value = "1"; //Update valve04 ON state
    mcApi.sensor().sendPayload(valve04); //send state
  
    //Update valve04 is running
    valveStatus.value3 = "value04";
    mcApi.variable().update(valveStatus);
  
    //Wait time
    Thread.sleep(delayTime);

    //Turn OFF valve04 and turn ON valve05
    valve04.value = "0"; //Update valve04 OFF state
    mcApi.sensor().sendPayload(valve04); //send state
    valve05.value = "1"; //Update valve05 ON state
    mcApi.sensor().sendPayload(valve05); //send state
  
    //Update valve05 is running
    valveStatus.value4 = "value05";
    mcApi.variable().update(valveStatus);
  
    //Wait time
    Thread.sleep(delayTime);

    //Turn OFF valve05 and turn ON valve06
    valve05.value = "0"; //Update valve05 OFF state
    mcApi.sensor().sendPayload(valve05); //send state
    valve06.value = "1"; //Update valve06 ON state
    mcApi.sensor().sendPayload(valve06); //send state
  
    //Update valve06 is running
    valveStatus.value5 = "value06";
    mcApi.variable().update(valveStatus);
  
    //Wait time
    Thread.sleep(delayTime);

    //Turn OFF valve06 and turn ON valve07
    valve06.value = "0"; //Update valve06 OFF state
    mcApi.sensor().sendPayload(valve06); //send state
    valve07.value = "1"; //Update valve07 ON state
    mcApi.sensor().sendPayload(valve07); //send state
  
    //Update valve06 is running
    valveStatus.value6 = "value07";
    mcApi.variable().update(valveStatus);
  
    //Wait time
    Thread.sleep(delayTime);


    //Turn OFF valve07 and turn ON valve08
    valve07.value = "0"; //Update valve07 OFF state
    mcApi.sensor().sendPayload(valve07); //send state
    valve08.value = "1"; //Update valve08 ON state
    mcApi.sensor().sendPayload(valve08); //send state
  
    //Update valve07 is running
    valveStatus.value7 = "value08";
    mcApi.variable().update(valveStatus);
  
    //Wait time
    Thread.sleep(delayTime);

    //Turn OFF valve08 and turn OFF master valve
    valve08.value = "0"; //Update valve08 OFF state
    mcApi.sensor().sendPayload(valve08); //send state
    masterValve.value = "0"; //Update master valve OFF state
    mcApi.sensor().sendPayload(masterValve); //send state
    
    //Update not running
    valveStatus.value = "stopped";
    valveStatus.value2 = "-";
    mcApi.variable().update(valveStatus);
    mcApi.logger().debug("Loop Through Valve Script Completed...");
  }else{
    mcApi.logger().warn("Loop Through Valve Script is already running...");
  }
}

Emenike

What am I doing wrong? I am posting the Nodes and Sensors just incase... Sensors Script.png

jkandasa

@Emenike Can you post your UID Tags and Variables repositorypage?

Emenike

Sorry @jkandasa, I have been on the move travelled for the Christmas Holiday. so I am away from my nodes and sensors. But I have the MYC on my laptop. so here are the data you requested for.

and the Variables - Variable Repisotory.png

jkandasa

@Emenike I do not find a variable Status in your variable repository screenshot, But you are trying to access it,

  var LoopThroughValves = mcApi.variable().get("Status");

Frustrated Newbie - Help with Nodes and Sensors

0

644

532

3.4k