problems with registering nodes and sensors

[Tag]

@mitjaxp

Strange, have you tried the clear-eeprom sketch to clear all the "saved" settings in the node, and then reload your sketch?

[mitjaxp]

@tag said in problems with registering nodes and sensors:

nd t

yes i try this

[Tag]

@mitjaxp

So if i understand correctly the following is happening:

1. You have a working node with a running example

2. a new sketch is uploaded to the node
   2.1 the node is deleted from mycontroller

3. node is started but is not seen in mycontroller.

Is this correct?

[mitjaxp]

yes exactly i was try https://www.mysensors.org/build/binary woks perfectly then i was try https://www.mysensors.org/build/relay was working also then try again binary and not working also relay not working now like it hac mycontroler something in cache... was already try delete browser cache can i delete any cache in mycontroller that affect ?

i also try other arduino board and same problem

[Tag]

@mitjaxp said in problems with registering nodes and sensors:

ycontroler something in cache... was already try delete browser cache can i delete any cache in mycontroller that affect ?

if you enable debug on the node, do you see it connect to the gateway?
Can you post the output? (we first need to figure out if the node is able to connect to the gateway, next step will be mycontroller)

[mitjaxp]

@tag said in problems with registering nodes and sensors:

e first need to figure out if the node is able to connect to

16 MCO:BGN:INIT NODE,CP=RNNNA---,VER=2.2.0
25 TSM:INIT
26 TSF:WUR:MS=0
33 TSM:INIT:TSP OK
35 !TSF:SID:FAIL,ID=0
37 TSM:FAIL:CNT=1
38 TSM:FAIL:DIS
40 TSF:TDI:TSL
10042 TSM:FAIL:RE-INIT
10044 TSM:INIT
10051 TSM:INIT:TSP OK
10053 !TSF:SID:FAIL,ID=0
10055 TSM:FAIL:CNT=2
10057 TSM:FAIL:DIS
10059 TSF:TDI:TSL```

[Tag]

@mitjaxp said in problems with registering nodes and sensors:

!TSF:SID:FAIL

Can you check this setting in mycontroller:

Settings --> system --> Register nodes automatically

Is this set to automatically?

Something else to try
If you set a static node id in your sketch, does that change anything?

#define MY_NODE_ID 25

(25 is just a number, please use a free non-assigned node number......)

[mitjaxp]

i have enabled and i try set it but now i thing it's not mycontroller i installed domoticz and same problem so must be on nodes

[Tag]

@mitjaxp said in problems with registering nodes and sensors:

i thing it's not mycontroll

Okay, well, maybe the mysensors forum can help you..... lots of knowledge there....
(Would appreciate if you tell us once solved )

[mitjaxp]

SOLVED!!!!! it make me crazy but finally i found on mysensors forum
@dallienl said in Building an Ethernet Gateway:

Had lots of issues getting this to work. The issue seems to be with the ethernet part, as I only have an ethernet board attached I removed the lines for the radio and the pin redirection. Still the code kept restarting all the time or just not being able to connect the controller.

AVR version of the Arduino 1.8.0 kit needs to be downgraded. I had 1.6.16 and downgraded to 1.6.11.

Open Arduino. Tools > Board: xxxxx > Boards manager... > Click "Arduino AVR Boards" > Select Version > 1.6.11

Recompile and you are good.

so i had to downgraded AVR version of the Arduino 1.8.0 kit and thats it i knew its smothing in arduino IDE

reply

[Tag]

@mitjaxp

Great news!!!
Many thanks for posting the solution here :thumbs_up: