MySensor auto node ID
-
@jkandasa said:
@benya I do not see any fault on your code. Can you check does your sketch already holds some id? Try to erase EEPROM and try again.
I cleared EEPROM and used bare minimum sketch:
#define MY_RADIO_NRF24 #define MY_BAUD_RATE 38400 #define MY_DEBUG #include <MySensors.h> #include <SPI.h> #define SENSOR_ID 1 #define OPEN 1 #define CLOSE 0 MyMessage msg(SENSOR_ID, V_TRIPPED); uint8_t value = OPEN; void presentation() { present(SENSOR_ID, S_DOOR); } void loop() { value = value == OPEN ? CLOSE : OPEN; send(msg.set(value)); sleep(10000); }
and node still fails to register:
0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1 10 TSM:INIT 12 TSF:WUR:MS=0 22 TSM:INIT:TSP OK 28 !TSF:SID:FAIL,ID=0 34 TSM:FAIL:CNT=1 38 TSM:FAIL:PDT 10045 TSM:FAIL:RE-INIT 10051 TSM:INIT 10061 TSM:INIT:TSP OK 10067 !TSF:SID:FAIL,ID=0 10074 TSM:FAIL:CNT=2 10080 TSM:FAIL:PDT 20086 TSM:FAIL:RE-INIT
-
As soon as I set specific NODE_ID:
#define MY_NODE_ID 1
node is able to connect:
0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1 10 TSM:INIT 12 TSF:WUR:MS=0 22 TSM:INIT:TSP OK 28 TSM:INIT:STATID=1 36 TSF:SID:OK,ID=1 43 TSM:FPAR 79 TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 292 TSF:MSG:READ,0-0-1,s=255,c=3,t=8,pt=1,l=1,sg=0:0 307 TSF:MSG:FPAR OK,ID=0,D=1 2101 TSM:FPAR:OK 2105 TSM:ID 2109 TSM:ID:OK 2113 TSM:UPL 2117 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1 2136 TSF:MSG:READ,0-0-1,s=255,c=3,t=25,pt=1,l=1,sg=0:1 2150 TSF:MSG:PONG RECV,HP=1 2158 TSM:UPL:OK 2162 TSM:READY:ID=1,PAR=0,DIS=1 2207 !TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=NACK:0100 4229 TSF:MSG:SEND,1-1-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=1,st=OK:2.1.1 4251 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0 6268 TSF:MSG:SEND,1-1-0-0,s=1,c=0,t=0,pt=0,l=0,sg=0,ft=0,st=OK: 6287 MCO:REG:REQ 6326 !TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=NACK:2 7239 TSF:MSG:READ,0-0-1,s=255,c=3,t=6,pt=0,l=6,sg=0:Metric 8382 !TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=1,st=NACK:2 10401 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=2,st=OK:2 10420 TSF:MSG:READ,0-0-1,s=255,c=3,t=27,pt=1,l=1,sg=0:1 10436 MCO:PIM:NODE REG=1 10442 MCO:BGN:INIT OK,TSP=1 10452 TSF:MSG:SEND,1-1-0-0,s=1,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:0 10471 MCO:SLP:MS=10000,SMS=0,I1=255,M1=255,I2=255,M2=255 10485 MCO:SLP:TPD 10491 MCO:SLP:WUP=-1
-
@benya Does your radio receives Rx pocket from gateway? Can you check gateway debug log?
-
@jkandasa
How could I check?
I posted logs already. -
@benya Enable debug message on gateway node, and capture log message
-
@jkandasa
Gateway log when node uses MY_NODE_ID=AUTO:mysgw: Starting gateway... mysgw: Protocol version - 2.2.0-beta mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.2.0-beta mysgw: TSF:LRT:OK mysgw: TSM:INIT mysgw: TSF:WUR:MS=0 mysgw: TSM:INIT:TSP OK mysgw: TSM:INIT:GW MODE mysgw: TSM:READY:ID=0,PAR=0,DIS=0 mysgw: MCO:REG:NOT NEEDED mysgw: MCO:BGN:STP mysgw: MCO:BGN:INIT OK,TSP=1
Node's log:
0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1 10 TSM:INIT 12 TSF:WUR:MS=0 22 TSM:INIT:TSP OK 28 !TSF:SID:FAIL,ID=0 34 TSM:FAIL:CNT=1 38 TSM:FAIL:PDT 10045 TSM:FAIL:RE-INIT 10051 TSM:INIT 10061 TSM:INIT:TSP OK 10067 !TSF:SID:FAIL,ID=0 10074 TSM:FAIL:CNT=2 10080 TSM:FAIL:PDT 20086 TSM:FAIL:RE-INIT 20092 TSM:INIT 20103 TSM:INIT:TSP OK 20109 !TSF:SID:FAIL,ID=0 20115 TSM:FAIL:CNT=3 20121 TSM:FAIL:PDT
Gateway log when node uses MY_NODE_ID=1:
mysgw: Starting gateway... mysgw: Protocol version - 2.2.0-beta mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.2.0-beta mysgw: TSF:LRT:OK mysgw: TSM:INIT mysgw: TSF:WUR:MS=0 mysgw: TSM:INIT:TSP OK mysgw: TSM:INIT:GW MODE mysgw: TSM:READY:ID=0,PAR=0,DIS=0 mysgw: MCO:REG:NOT NEEDED mysgw: MCO:BGN:STP mysgw: MCO:BGN:INIT OK,TSP=1 mysgw: TSF:MSG:READ,1-1-255,s=255,c=3,t=7,pt=0,l=0,sg=0: mysgw: TSF:MSG:BC mysgw: TSF:MSG:FPAR REQ,ID=1 mysgw: TSF:PNG:SEND,TO=0 mysgw: TSF:CKU:OK mysgw: TSF:MSG:GWL OK mysgw: TSF:MSG:SEND,0-0-1-1,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0 mysgw: TSF:MSG:READ,1-1-0,s=255,c=3,t=24,pt=1,l=1,sg=0:1 mysgw: TSF:MSG:PINGED,ID=1,HP=1 mysgw: TSF:MSG:SEND,0-0-1-1,s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=OK:1 mysgw: TSF:MSG:READ,1-1-0,s=255,c=3,t=15,pt=6,l=2,sg=0:0100 mysgw: TSF:MSG:SEND,0-0-1-1,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100 mysgw: TSF:MSG:READ,1-1-0,s=255,c=0,t=17,pt=0,l=5,sg=0:2.1.1 mysgw: TSF:MSG:READ,1-1-0,s=255,c=3,t=6,pt=1,l=1,sg=0:0 mysgw: TSF:MSG:READ,1-1-0,s=1,c=0,t=0,pt=0,l=0,sg=0: mysgw: TSF:MSG:READ,1-1-0,s=255,c=3,t=26,pt=1,l=1,sg=0:2 mysgw: !TSF:MSG:SEND,0-0-1-1,s=255,c=3,t=27,pt=1,l=1,sg=0,ft=0,st=NACK:1 mysgw: TSF:MSG:READ,1-1-0,s=255,c=3,t=26,pt=1,l=1,sg=0:2 mysgw: TSF:MSG:SEND,0-0-1-1,s=255,c=3,t=27,pt=1,l=1,sg=0,ft=0,st=OK:1 mysgw: TSF:MSG:READ,1-1-0,s=1,c=1,t=16,pt=1,l=1,sg=0:0 mysgw: TSF:MSG:READ,1-1-0,s=1,c=1,t=16,pt=1,l=1,sg=0:1
Node log:
0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1 10 TSM:INIT 12 TSF:WUR:MS=0 22 TSM:INIT:TSP OK 28 TSM:INIT:STATID=1 36 TSF:SID:OK,ID=1 43 TSM:FPAR 79 TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 354 TSF:MSG:READ,0-0-1,s=255,c=3,t=8,pt=1,l=1,sg=0:0 368 TSF:MSG:FPAR OK,ID=0,D=1 2101 TSM:FPAR:OK 2105 TSM:ID 2109 TSM:ID:OK 2113 TSM:UPL 2117 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1 2136 TSF:MSG:READ,0-0-1,s=255,c=3,t=25,pt=1,l=1,sg=0:1 2150 TSF:MSG:PONG RECV,HP=1 2158 TSM:UPL:OK 2162 TSM:READY:ID=1,PAR=0,DIS=1 2207 !TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=NACK:0100 2228 TSF:MSG:READ,0-0-1,s=255,c=3,t=15,pt=6,l=2,sg=0:0100 2256 TSF:MSG:SEND,1-1-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=1,st=OK:2.1.1 2293 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0 4313 TSF:MSG:SEND,1-1-0-0,s=1,c=0,t=0,pt=0,l=0,sg=0,ft=0,st=OK: 4331 MCO:REG:REQ 4370 !TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=NACK:2 6397 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=1,st=OK:2 6416 TSF:MSG:READ,0-0-1,s=255,c=3,t=27,pt=1,l=1,sg=0:1 6430 MCO:PIM:NODE REG=1 6436 MCO:BGN:INIT OK,TSP=1 6453 TSF:MSG:SEND,1-1-0-0,s=1,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:0 6469 MCO:SLP:MS=10000,SMS=0,I1=255,M1=255,I2=255,M2=255 6483 MCO:SLP:TPD 6490 MCO:SLP:WUP=-1
-
@benya Thank you for the log and your patience. You can see from the gateway log, when you have enabled
NODE_ID=AUTO
, the gateway does not receive any request from the node. So it is problem between node and gateway. As gateway didn't receive and node id request MyController also do not know about it.You have to check with MySensors guys. I request to go to the previous version of MySensors as well as the current version of the MySensors library. This issue might be with specific version too.
-
@jkandasa Turned out that EEPROM was not cleared properly with 0xFF
-
@benya how did you see that it wasn't fully cleared, what script did you use to clear the EEPROM, are you using AUTO node id?
-
@mpp Guys in MySensors forum noticed I cleared EEPROM with zeros instead of 0xFF.