miscellaneous question

JeeLet

I have ~~nothing~~, not understood everything.

so the Arduino that I connect to my Odroid
is not only a gateway (a bridge)
but it's also a Node, but that is not used ?

you can give me a small piece of sketch that I place in the "gateway" for me MyC think that the Node 0 is used for what things.

But maybe I will test the node to node (0 with 55) to check the reliability of the CAN bus, a cyclic thing.

question:
there is a LOG file to recover the information of Active/Inactive ???

Thanks

jkandasa

@JeeLet This is just an indicator that your node didn't send data for a specified period of time and marked as Down. But nothing affected in functionality. It is just a visual indicator, MyController assumes that your node is Down, as it is not receiving any data for a while. This status will not impact anything.
Please let me know, if still, this is not clear, I will try to explain in different way.

there is a LOG file to recover the information of Active/Inactive ???

There is no log for this

JeeLet

Hello jkandasa
thank you for your pedagogical patience

But the gateway, basically, its primary function is a bridgehead between the constellation of sensors MyS and MyC.

it doesn't have to be a node,

and for "This is just an indicator" for me Green=cool, Red=danger ..... an Orange for "you have seen"

on the other hand not being able to use this feature of the "no data" indicator routine is a shame.

Can you use it for a time stamp to monitor the nodes?

Yes MyController is good ... More questions soon

Thanks

jkandasa

@JeeLet said in miscellaneous question:

But the gateway, basically, its primary function is a bridgehead between the constellation of sensors MyS and MyC.
it doesn't have to be a node,

MySensors gateway can be a node too. So we have created a node with id 0. Example: https://forum.mysensors.org/topic/4765/the-sensor-network/41

and for "This is just an indicator" for me Green=cool, Red=danger ..... an Orange for "you have seen"

To understand quickly I mentioned that it is just an indicator. beyond this, you can trigger a task based on the node status change.
example: perform gateway reload if there is a node status changed to down(in mysensors node 0), send telegram, etc.,

on the other hand not being able to use this feature of the "no data" indicator routine is a shame.

I do not get this question. Can you please elaborate?

Can you use it for a time stamp to monitor the nodes?

Node status updated using lastSeen. When there is a message received for the node, LastSeen has been updated.

JeeLet

Ouch
the translation of the languages, or the puns are not clear

I simplify my text, and also you have partly answered my question.

how to use "LastSeen"
. to make an action. but how?
. the value can it be put in a widget, for a synoptic with the dashboard
( to have a dashboard of some elements of the system, monitoring on a single page of several different families, states and temperatures

the concept of
synoptic
supervisor

to have on the same page, an overview of the important elements.
. System alarms (MyS, status of nodes and other elements)

Equipment alarms (house, temperatures, intrusion ...)

jkandasa

@JeeLet It is possible to put the node status on the dashboard, select Node resource and use the key state.status. To know other possible keys just look at node edit page and yaml view. nested keys can be formed with .

JeeLet

I still don't understand some of the subtleties of MyController

I tested as you say, but nothing works.

the Yaml file

title: Panel Title
showTitle: true
scrollbarDisabled: false
static: false
type: widget_control_panel
layout:
  w: 28
  h: 54
  x: 0
  'y': 90
config:
  resource:
    filters:
      metricType: binary
    type: field
  resources:
    - control:
        config:
          options:
            state.status: ''
        type: options_tab
      resource:
        nameKey: stat56
        quickId: GwCan.56
        type: node
    - control:
        config:
          options:
            state.status: ''
        type: options_tab
      resource:
        nameKey: stat55
        quickId: GwCan.55
        type: node
  tableView: true
  type: mixed_control

putting the status of the nodes and gateway on the dashboard is a good thing.

jkandasa

@JeeLet I will try to document MyController things,
for now you can go with the followings, It shows list of nodes and gateways,
If you want to display on the mixed resources, I can give an example, let me know

Nodes

id: 8cd43dbd-b873-4712-b855-789a6501e673
title: Nodes Status
showTitle: true
scrollbarDisabled: false
static: false
type: widget_utilization_panel
layout:
  w: 33
  h: 117
  x: 31
  'y': 0
config:
  resource:
    displayName: true
    filter: {}
    filterType: detailed_filter
    isMixedResources: false
    limit: 10
    nameKey: name
    quickId: ''
    resources: []
    roundDecimal: 0
    timestampKey: lastSeen
    type: node
    unit: ''
    valueKey: state.status
  table:
    displayStatusPercentage: false
    hideBorder: false
    hideStatusColumn: true
    hideValueColumn: false
    maximumValue: 100
    minimumValue: 0
    thresholds: {}
  type: table

Gateways

id: bf2e078a-b4eb-4df2-b119-773ae47909ef
title: Gateway Status
showTitle: true
scrollbarDisabled: false
static: false
type: widget_utilization_panel
layout:
  w: 31
  h: 118
  x: 64
  'y': 0
config:
  resource:
    displayName: true
    filter: {}
    filterType: detailed_filter
    isMixedResources: false
    limit: 10
    nameKey: id
    quickId: ''
    resources: []
    roundDecimal: 0
    timestampKey: state.since
    type: gateway
    unit: ''
    valueKey: state.status
  table:
    displayStatusPercentage: true
    hideBorder: false
    hideStatusColumn: true
    hideValueColumn: false
    maximumValue: 100
    minimumValue: 0
    thresholds: {}
  type: table

JeeLet

Thank you @jkandasa

it's very good like that , it works well

I put at 10minute /Node State Updater/ Execution Interval

"I'll try to document things MyController," ... yes the Labels / Key /Value part
. what tree structure
. family ? structure ???
. how to use them ?? create them ??

jkandasa

@JeeLet said in miscellaneous question:

. what tree structure
. family ? structure ???
. how to use them ?? create them ??

You can refer the source code for all the keys. I will create document for this. but it will time

JeeLet

Hello jkandasa

It's been a long time, I hope you are well.

a question about the visualization of the curves of measurements.

On my Dashboard I have to add a widget to visualize the values with the
"Field Details" which is more flexible to use.

here is an image for the explanation text alternatif

In the example, there is no way to do it by clicking on the element
V_LIGHT_LEVEL element of the "LuX panel"?

Thanks

JeeLet

unnecessary message is cumbersome

... Delete .....

skywatch

your issue could be in a number of places but if it helps for the BH1750 sensor I use V_LEVEL and S_LIGHT_LEVEL

MC does not need to know what the units are as you can change this to whatever you want.

JeeLet

Hello

I just realized that I've done something wrong

S_LIGHT_LEVEL    ---  to --->     S_LEVEL

thank you skywatch for cleaning my glasses

JeeLet

there are days that are not easy

the Lux Unit does not want to be considered
the part of the Yaml file

fieldId: V_LEVEL
name: V_LEVEL
metricType: gauge_float
....
unit: ''    <------ ????
labels:
  ms_node_id: '58'
  ms_sensor_id: '5'
  ms_type: '37'
  ms_type_string: V_LEVEL

I give it the "Lux" value but it doesn't keep it

jkandasa

@JeeLet I give it the "Lux" value but it doesn't keep it

You can ignore the default unit by adding a label ignore_unit:true, this is applicable for name and metric type.
if you change any of the following from the default to custom value use ignore_* label.

Example:

I changed the name, unit, and metricType

labels:
  ignore_name: "true"
  ignore_unit: "true"
  ignore_metric_type: "true"

to know more about defined labels: https://github.com/mycontroller-org/server/blob/6ce7df3a32325af16fb87b638cd45c58110cbe1d/pkg/types/labels.go

jkandasa

@JeeLet said in miscellaneous question:

In the example, there is no way to do it by clicking on the element

I could not find a way to click from legend. I have created a GH issue to track this. In the future we may resolve this. https://github.com/mycontroller-org/console-web/issues/11

JeeLet

Thank you
The Lux are well La
(ignore_unit:true is good)

For my 2nd question "click from the legend"

here I talked about the problem that when you are in "Edit" mode of a widget
https://forum.mycontroller.org/topic/510/vokoscreen

can we put this function back when we are in "Visualization" mode?

clicking on the curve is as good, even better

jkandasa

@JeeLet said in miscellaneous question:

can we put this function back when we are in "Visualization" mode?

It is back already. the group chart and mixed chart is not designed the way other charts behave. So drill down is not implemented in those charts. I will find a way for this.

JeeLet

miscellaneous question

Nodes

Gateways

Example:

1

610

531

3.4k