serial, Ethernet to MQTT

jkandasa

Hi,

I have developed a new MQTT bridge to convert from serial, ethernet to MQTT.
Supports for MySensors.
You can have more than one serial ports and/or ethernet connections.
If you are interested in, https://github.com/mycontroller-org/2mqtt
Thanks!

j54n1n

Hello @jkandasa,

I was testing if I could use the old workflow that we used in our weather station school project, using an Arduino with RFM69 radio as a serial gateway broadcasting messages to local Mosquitto MQTT broker from where MyController then picks up the messages.

I noticed that compared to your new v2 MyController's internal serial gateway, your 2mqtt bridge consumes more CPU cycles.

Compare that when your builtin serial gateway is enabled from within MyController v2 UI with low CPU usage:

to your standalone 2mqtt bridge with higher CPU usage:

And I double checked that the builtin serial gateway was disabled from within the MyController v2 UI. I even tried to terminate MyController and checked with MQTT.fx if data was incoming from the bridge and I can confirm that I was still receiving valid data besides the high CPU usage.

I was using your suggested settings as mentioned in your documentation MySensors | MyController.org and from your readme file on 2mqtt/README.md.

Is this normal, or should I file a issue on your GitHub repository?

Kind regards

jkandasa

Hi, @j54n1n Thanks for the detailed report.
It does not look normal. It can be a bug in 2mqtt
Can you share your configuration details used in 2mqtt? (remove sensitive details)

j54n1n

@jkandasa yes sure, I was not using any special configuration. I adapted the config file only to suit the configuration that we used before.

Here we go for the config.yaml file:

logger:
  mode: development
  encoding: console
  level: info

adapters:
  - name: adapter1
    enabled: true
    reconnect_delay: 20s
    provider: mysensors_v2
    source:
      type: serial
      port: /dev/serial0
      baud_rate: 115200
      transmit_pre_delay: 10ms
    mqtt:
      broker: tcp://127.0.0.1:1883
      insecure_skip_verify: false
      username:
      password:
      subscribe: mysensors-in/#
      publish: mysensors-out
      qos: 0
      transmit_pre_delay: 0s
      reconnect_delay: 5s

  - name: adapter2
    enabled: false
    reconnect_delay: 20s
    provider: mysensors_v2
    source:
      type: ethernet
      server: tcp://192.168.10.21:5003
      transmit_pre_delay: 10ms
    mqtt:
      broker: tcp://192.168.10.21:1883
      insecure_skip_verify: false
      username:
      password:
      subscribe: in_nrf24/#
      publish: out_nrf24
      qos: 0
      transmit_pre_delay: 0s
      reconnect_delay: 5s

  - name: adapter3
    enabled: false
    reconnect_delay: 20s
    provider: raw
    source:
      type: serial
      port: /dev/ttyUSB0
      baud_rate: 115200
      transmit_pre_delay: 10ms
      message_splitter: 10
    mqtt:
      broker: tcp://192.168.10.21:1883
      insecure_skip_verify: false
      username:
      password:
      subscribe: in/my_topic
      publish: out/my_topic
      qos: 0
      transmit_pre_delay: 0s
      reconnect_delay: 5s

and for my environment on the Raspberry Pi:

$ cat /etc/*release
PRETTY_NAME="Raspbian GNU/Linux 10 (buster)"
NAME="Raspbian GNU/Linux"
VERSION_ID="10"
VERSION="10 (buster)"
VERSION_CODENAME=buster
ID=raspbian
ID_LIKE=debian
HOME_URL="http://www.raspbian.org/"
SUPPORT_URL="http://www.raspbian.org/RaspbianForums"
BUG_REPORT_URL="http://www.raspbian.org/RaspbianBugs"

$ uname -a
Linux metteo-dev2 5.10.17-v7+ #1421 SMP Thu May 27 13:59:01 BST 2021 armv7l GNU/Linux

$ ls -l /dev/serial0
lrwxrwxrwx 1 root root 7 Jul 14 20:00 /dev/serial0 -> ttyAMA0

$ ls -l /dev/ttyAMA0
crw-rw---- 1 root dialout 204, 64 Jul 14 20:00 /dev/ttyAMA0

$ groups pi
pi : pi adm dialout cdrom sudo audio video plugdev games users input netdev spi i2c gpio lpadmin

$ apt-cache policy mosquitto
mosquitto:
  Installed: 1.5.7-1+deb10u1
  Candidate: 1.5.7-1+deb10u1
  Version table:
 *** 1.5.7-1+deb10u1 500
        500 http://raspbian.raspberrypi.org/raspbian buster/main armhf Packages
        100 /var/lib/dpkg/status

Thanks in advance

jkandasa

@j54n1n Thanks for the detailed configuration. I try to create this setup in my environment.

jkandasa

@j54n1n I can reproduce this issue. kindly file a bug. I will work on it. Thanks!

j54n1n

@jkandasa thanks, ok here is the link to the issue: https://github.com/mycontroller-org/2mqtt/issues/1

Cheers j54n1n

jkandasa

Thnaks, @j54n1n!

jkandasa

@j54n1n I have fixed the issue, can you please verify it in the master build?

j54n1n

@jkandasa thanks, yes now I get low CPU usage.

Nice work ^^

jkandasa

Thanks @j54n1n
I believe I my change will not impact the functionality
Please let me know if you see a different behavior in the recent build

j54n1n

@jkandasa Ok, I quickly looked through it with MQTT.fx and it seems to be fine.

Thanks again. Now I will start looking for strange behaviors with MySensors in your MyController v2.

jkandasa

@j54n1n thanks again! please report back if you find any

serial, Ethernet to MQTT

1

650

520

3.4k