Strange routing and sensor assignments

Clone Tv

Collected a test circuit from a gateway and one sensor. Hardware in both cases is the same, Vetos d1 r1 + nRF24L01.

I registered the gateway to MQTT myself, the rest was picked up automatically. But, I'm a little confused, because in my opinion everything was determined incorrectly ..
And when testing MQTT topics from an external dash program, the paths of topics look very strange. For example:

gw-out/21/1/1/0/16
gw-in/0/21/1

and the topology doesn't look natural

Sketch Gateway:

#define MY_WIFI_SSID "xxxx"
#define MY_WIFI_PASSWORD "xxxxxxx"

#define MY_DEBUG
#define MY_SPECIAL_DEBUG
#define MY_DEBUG_VERBOSE
#define MY_DEBUG_VERBOSE_RF24
#define MY_DEBUG_VERBOSE_SIGNING

#define MY_RADIO_RF24
#define MY_RF24_PA_LEVEL RF24_PA_HIGH
// #define MY_RF24_ENABLE_ENCRYPTION

#define MY_GATEWAY_ESP8266
#define MY_REPEATER_FEATURE

#define MY_NODE_ID 0
#define MY_BAUD_RATE 115200
#define MY_GATEWAY_MQTT_CLIENT
#define MY_MQTT_PUBLISH_TOPIC_PREFIX "gw-out"
#define MY_MQTT_SUBSCRIBE_TOPIC_PREFIX "gw-in"
#define MY_MQTT_CLIENT_ID "myqw-mqtt-client"
#define MY_HOSTNAME "ESP8266_MQTT_GW"
#define MY_CONTROLLER_IP_ADDRESS 192, 168, 0, 105
#define MY_PORT 1883
#define MY_GATEWAY_MAX_CLIENTS 8
#define MY_SMART_SLEEP_WAIT_DURATION_MS (2000ul)
#define NODE_SENSOR_ID 1

....

void presentation() {
  sendSketchInfo("ESP MQTT Gateway", "1.1");
}

Sketch Fake Sensor:

#define MY_DEBUG
#define MY_DEBUG_VERBOSE_SIGNING

#define MY_RADIO_RF24
#define MY_RF24_CE_PIN D2
#define MY_RF24_CS_PIN D4
#define MY_RF24_PA_LEVEL RF24_PA_HIGH
//#define MY_RF24_ENABLE_ENCRYPTION

#define MY_BAUD_RATE 115200
#define MY_NODE_ID (AUTO)
#define MY_PARENT_NODE_ID 0
#define MY_PARENT_NODE_IS_STATIC

#define MY_HOSTNAME "FAKE_SENSOR_1"
#include <MySensors.h>

#define OPEN 1
#define CLOSE 0
#define CHILD_ID 1
#define NODE_SENSOR_ID 1

MyMessage msg(CHILD_ID, V_TRIPPED);

int cnt = 0;
uint8_t value = OPEN;

void setup() {}
void presentation()
{
  sendSketchInfo("Fake Sensor", "1.1");
  present(CHILD_ID, S_DOOR);
}

void loop()
{
  if (++cnt >= 60 ) {
    value = ((value == OPEN) ? CLOSE : OPEN);
    send(msg.set(value));
    Serial.printf("Set DOOR status = %d\n", (int) value);
    cnt = 0;
  }
  delay(100);
}

Gateway RF:

19125773 RF24:WBR:REG=7,VAL=64
19125776 TSF:MSG:READ,21-21-0,s=1,c=1,t=16,pt=1,l=1,sg=0:1
19125781 GWT:TPS:TOPIC=gw-out/21/1/1/0/16,MSG SENT
19131805 RF24:RXM:LEN=8
19131807 RF24:WBR:REG=7,VAL=64
19131810 TSF:MSG:READ,21-21-0,s=1,c=1,t=16,pt=1,l=1,sg=0:0
19131816 GWT:TPS:TOPIC=gw-out/21/1/1/0/16,MSG SENT
19137845 RF24:RXM:LEN=8
19137847 RF24:WBR:REG=7,VAL=64
19137850 TSF:MSG:READ,21-21-0,s=1,c=1,t=16,pt=1,l=1,sg=0:1
19137856 GWT:TPS:TOPIC=gw-out/21/1/1/0/16,MSG SENT
19143892 RF24:RXM:LEN=8
19143894 RF24:WBR:REG=7,VAL=64
19143897 TSF:MSG:READ,21-21-0,s=1,c=1,t=16,pt=1,l=1,sg=0:0
19143903 GWT:TPS:TOPIC=gw-out/21/1/1/0/16,MSG SENT
19149944 RF24:RXM:LEN=8
19149946 RF24:WBR:REG=7,VAL=64
19149949 TSF:MSG:READ,21-21-0,s=1,c=1,t=16,pt=1,l=1,sg=0:1
19149955 GWT:TPS:TOPIC=gw-out/21/1/1/0/16,MSG SENT
19155988 RF24:RXM:LEN=8
19155990 RF24:WBR:REG=7,VAL=64
19155993 TSF:MSG:READ,21-21-0,s=1,c=1,t=16,pt=1,l=1,sg=0:0
19155999 GWT:TPS:TOPIC=gw-out/21/1/1/0/16,MSG SENT

Sensor RF:

Set DOOR status = 0
19162221 TSF:MSG:SEND,21-21-0-0,s=1,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:1
Set DOOR status = 1
19168276 TSF:MSG:SEND,21-21-0-0,s=1,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:0
Set DOOR status = 0
19174328 TSF:MSG:SEND,21-21-0-0,s=1,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:1
Set DOOR status = 1
19180364 TSF:MSG:SEND,21-21-0-0,s=1,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:0
Set DOOR status = 0
19186403 TSF:MSG:SEND,21-21-0-0,s=1,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:1
Set DOOR status = 1
19192436 TSF:MSG:SEND,21-21-0-0,s=1,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:0
Set DOOR status = 0
19198493 TSF:MSG:SEND,21-21-0-0,s=1,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:1
Set DOOR status = 1
19204541 TSF:MSG:SEND,21-21-0-0,s=1,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:0
Set DOOR status = 0
19210586 TSF:MSG:SEND,21-21-0-0,s=1,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:1
Set DOOR status = 1
19216634 TSF:MSG:SEND,21-21-0-0,s=1,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:0
Set DOOR status = 0
19222695 TSF:MSG:SEND,21-21-0-0,s=1,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:1
Set DOOR status = 1

Gateway settings:

Nodes settings:

how to be in such a situation?

jkandasa

@Clone-Tv do you see any error log related to this on mycontroller.log?
to get complete topology, on the gateway page select a gateway and on actions click, Discover and the get node information click Refresh nodes info

Clone Tv

@jkandasa

Thanks for the quick reply, but I did not look at the log at the time of adding. Or rather, no recordings caught my attention when I watched it later! With sensor detection and information I tried it, unfortunately the topology hasn't changed. It seems to me that this is due to the fact that the auto gateway is registered in the repeater state. I will check this later.

I have one more question: how to change the built-in MQTT broker to use SSL?
The various options for moquette described in the myController configuration do not change its initialization..
(I guess I'll create a separate question on this topic )

Strange routing and sensor assignments

1

650

520

3.4k