RFLink message not decoded due to NumberFormatException: Infinite or NaN



  • Hello,
    I have a MyController installation on a RaspberryPi
    Version 1.5.0
    Database schema revision
    1.04.06 - 2018 Dec 04
    Database type
    H2 database embedded

    Java virtual machine specification

    VM vendor
    Oracle Corporation
    VM name
    Java HotSpot(TM) Client VM
    VM version
    1.8.0_241-b07
    Java home
    /opt/jdk1.8.0_241/jre

    I get this error only in WINDIR WINGS message
    for example this message

    20;4e;Alecto V1;ID=0005;WINDIR=0012;WINGS=001c;BAT=OK;\r
    

    I get this error
    2020-05-02 17:20:14,053 ERROR [Thread-26] [org.mycontroller.standalone.gateway.serial.SerialDataListenerjSerialComm:201] Exception, RawMessage:[20;4e;Alecto V1;ID=0005;WINDIR=0012;WINGS=001c;BAT=OK;\r]
    java.lang.NumberFormatException: Infinite or NaN
    at java.math.BigDecimal.<init>(BigDecimal.java:898)
    at java.math.BigDecimal.<init>(BigDecimal.java:875)
    at org.mycontroller.standalone.utils.McUtils.getDoubleAsString(McUtils.java:106)
    at org.mycontroller.standalone.utils.McUtils.getDoubleAsString(McUtils.java:117)
    at org.mycontroller.standalone.provider.rflink.RFLink.getPayload(RFLink.java:112)
    at org.mycontroller.standalone.provider.rflink.RFLink.getPayload(RFLink.java:116)
    at org.mycontroller.standalone.provider.rflink.MessageParserRFLink.get(MessageParserRFLink.java:198)
    at org.mycontroller.standalone.provider.rflink.MessageParserRFLink.getMessage(MessageParserRFLink.java:130)
    at org.mycontroller.standalone.provider.rflink.MessageParserRFLink.getMessage(MessageParserRFLink.java:39)
    at org.mycontroller.standalone.gateway.serial.SerialDataListenerjSerialComm.serialEvent(SerialDriverJSerialComm.java:170)
    at com.fazecast.jSerialComm.SerialPort$SerialPortEventListener.waitForSerialEvent(SerialPort.java:937)
    at com.fazecast.jSerialComm.SerialPort$SerialPortEventListener$1.run(SerialPort.java:885)
    at java.lang.Thread.run(Thread.java:748)

    It happens only with this message, RAIN, TEMP & HUM and WINSP are decoded.



  • @zoomx
    I guess that WINSP = windspeed and that WINDIR = wind direction and WINGS = wind ground speed. Is that right?

    If you connect the node to a PC and view data sent via arduino serial monitor what does it show for those values?

    I had issues with DHT11 sensor which occasionally gave a NAN for a reading. I solved this by testing for NAN in the node sketch and not transmitting the value if NAN was detected.

    The full code of your node would help.



  • I opened an issue in github also.

    RFlink protocol is here

    http://www.rflink.nl/blog2/protref

    The error message is referred to the message show above, this one
    20;4e;Alecto V1;ID=0005;WINDIR=0012;WINGS=001c;BAT=OK;\r

    20 mean a messagr from RFlink
    4e is the message number
    ID is the sensor ID
    WINDIR is the wind direction
    WINGS is the wind speed gust

    Al messages are in ASCIII, there is not any NaN or strange values like the DHT ones.

    It happens with all WINDIR messages, no one is decoded.

    Data are captured and decoded from a meteo station sensors at 433MHz

    But you give me a good suggestion, maybe there is a character in message not printed in the error, so I will check on a PC in HEX also.

    Edit: Check done, all ascii chars plus CR+LF at the end

    I don't understand why this happens on this message and not with others.
    I watched on my controllers code and I don't see any bug.


Log in to reply
 

Suggested Topics

4
Online

573
Users

460
Topics

2.8k
Posts