• header.categories
    • header.recent
    • header.tags
    • header.popular
    • register
    • login

    Cant get OTA to start

    scheduled pinned locked moved Troubleshooting
    11 posts 2 posters 1.4k views 1 watching
    loading-more-posts
    • oldest-to-newest
    • newest-to-oldest
    • most-votes
    reply
    • reply-as-topic
    guest-login-reply
    deleted-message
    • jkandasaJ offline
      jkandasa @aliasjim
      global:last-edited-by,

      @aliasjim can you uncheck(disable) Stream ack enabled in your gateway and try again?

      one-reply-to-this-post last-reply-time reply quote 0
      • A offline
        aliasjim
        global:last-edited-by,

        Hi it was allready off. This was the problem before. After i unchecked it it started the OTA once but didn't finish successfully

        jkandasaJ one-reply-to-this-post last-reply-time reply quote 0
        • jkandasaJ offline
          jkandasa @aliasjim
          global:last-edited-by, jkandasa

          @aliasjim Which bootloader are you using?
          is your MQTT broker sits on the same network?

          A one-reply-to-this-post last-reply-time reply quote 0
          • A offline
            aliasjim
            global:last-edited-by, aliasjim

            i'm using MYSbotloader and i can ping the mqtt gateway. It allso shows as online in mycontroller. The broker is allso online because i can see the messages in my mqtt client on the desktop

            one-reply-to-this-post last-reply-time reply quote 0
            • A offline
              aliasjim @jkandasa
              global:last-edited-by,

              @jkandasa Am i right to think that if i have an empty sketch on the node and a FW is appointed to this node in mycontroller, mycontroller will update the nodes FW automaticly or at least after rebooting the node?

              jkandasaJ one-reply-to-this-post last-reply-time reply quote 0
              • jkandasaJ offline
                jkandasa @aliasjim
                global:last-edited-by,

                @aliasjim After rebooting the MYSBootloader node, it will ask firmware details. MyController will respond for that. Each block should be requested by the node.

                A one-reply-to-this-post last-reply-time reply quote 0
                • A offline
                  aliasjim @jkandasa
                  global:last-edited-by, aliasjim

                  @jkandasa In other words the problem lies with the node, since it doesn't request a FW block?

                  I'm using FW compiled for CH5, do you think this could be a problem? GW is allso programmed to use channel 5

                  jkandasaJ one-reply-to-this-post last-reply-time reply quote 0
                  • jkandasaJ offline
                    jkandasa @aliasjim
                    global:last-edited-by, jkandasa

                    @aliasjim Yes, maybe coverage issue. I had a similar type of issue with cheap chines clone board. Then I moved to Dualoptiboot, and no issues.

                    https://www.mysensors.org/about/fota

                    I'm using FW compiled for CH5, do you think this could be a problem? GW is allso programmed to use channel 5

                    If it is a problem, Gateway won't receive a single pocket from network, seems all works ok, other than OTA

                    A one-reply-to-this-post last-reply-time reply quote 0
                    • A offline
                      aliasjim @jkandasa
                      global:last-edited-by,

                      @jkandasa Indeed, i just pluged a premium shielded radio into my node and now the FW blocks are flying through my mqtt client. Its just strange that normal operation works just fine with the junk radios. Wich i knew this before i bought 50 of them ☹ 😖

                      A one-reply-to-this-post last-reply-time reply quote 0
                      • A offline
                        aliasjim @aliasjim
                        global:last-edited-by,

                        @aliasjim I noticed the MYSbootloader defaults to PA level MAX. When i use this PA level with my nodes in normal operation they don't function eigther. I might try with a bootloader compiled with lower PA level, maybe, just maybe i will get lucky. Now i only need to find someone who is willing to compile it for me😀

                        one-reply-to-this-post last-reply-time reply quote 0
                        • first-post
                          last-post

                        0

                        online

                        644

                        users

                        532

                        topics

                        3.4k

                        posts
                        Copyright © 2015-2025 MyController.org | Contributors | Localization