Mycontroller 2.x ideas
-
Now you mention it it would be nice to have an "and" / "or "condition in the rules section...
-
"and before 25, December 2017, version 1.1.0 will be available for the public"
Ahem.........
I am sure it will be well worth waiting for
-
@skywatch Thank you for the excellent feedback on 2.x release.
Just now release 1.1.0.Final
-
Another thing myc needs is 'real world' feedback on the dashboards. - I'll explain the problem....
I have a page with 4 switches which are used to turn power on/off to devices via a 4 relay board. It works well. But if the node goes down for any reason the dashboard for that room does not show this and the switches still show an on/off status even though the node isn't responding.
So if I were to turn on a light or heater, it would show as being on in the dashboard while in real life they are still off. I guess this goes with the 'ack' processing I mentioned before, but its an issue I had just now with no sound from the amplifier for this very reason. MYC showed the amplifier as 'ON' but the node was down (due to the robot vacuum chewing the cable and pulling it out under the unit ....Grrrr....) and so no sound..... This would be really bad with electronic door locks and some other systems (like thinking you turned off the garden watering system only to come home to find your lovely lawn replaced by a paddy field!)..... -
@skywatch Yes, it is a good feature. I hope this will be covered by ACK response. Which is not supported at this moment.
-
It would be a bonus if there was an easy way to set up MYC to store all sensor data on an external lan server/nas running mysql.
But I suppose that if the server/nas were to fail then data would be lost, but MYC pi should still function - So maybe have MYC push data to the serve/nas at a user selectable intervals keeping only most recent data on pi and switching to pi storage if the server/nas becomes unreachable?
-
@tag said in Mycontroller 2.x ideas:
I am using InfluxDB for approx 1 week now where mycontroller simply "dumps" the data. This is a really cool feature. (when you mention influx are you planning to use the complete "TICK" stack which influxDB is part off?)
I also really like the philosophy of the TICK stack.
I just try the rest of the TICK programs (Chronograf,Capacitor,Telegraf) and so far very pleased with their capabilities.
It would be very cool to integrate into the MyController 2.0 a complete TICK stack. -
Good point
IMHO the "TICK" stack is very complex, and therefore maybe not so suitable for a larger audience, the beauty of mycontroller is that it is relatively easy to install and use.
InfluxDB can be setup automatically..Another thing that needs to be taken into account is that the TICK stack is very resource hungry (ofcourse depending on the load from the sensor network), the OrangePIzero will have a hard time with just 512MB memory... even 1GB is small for the complete stack.
Just my 2 cents..
-
@Tag
Maybe you're right. I have not tried to load TICKstack with a lot of data streams from sensors. I installed all parts of TICKstack's and I'm studying the possibilities of this system with one temperature data stream and three relays.The memory capacity of Orange Pi Zero is still sufficient.Maybe then it makes sense to provide interfaces for the interaction of MyController 2.X with Kapacitors, Cronograf and InfluxDB, and TICKstack itself should be installed as an option?
I want to find a simple and beautiful dashboard with drag and drop programming. -
@wanvo
Mycontroller is beautifull
Try influx and grafana4 this will get you a highly customizable dashboard with all the stuff you want.
I did a setup of mysenors --> mycontroller --> influxdb --> Grafana4 and it works, but it is no easy setup. and will definitely not run on one single OPI0... CPU will be continuously in high performance mode and the OPI0 will get very very hot....In this setup mycontroller is handling the relays....
-
How is Grafana better than the built-in Dashboard of Cronograf? Cronograf weakly loads the processor and quickly runs on OrangePiZero. He really does not have a mechanism for controlling the relay or other devices. So far I have not figured out how to combine graphics and buttons on the same control panel. It may be necessary to use NodeRed and organize a virtual MQTT node.
-
-
Well the minimal system requirements give an indication on what hardware should be used. OPI0 is from a memory perspective a little "light". anyway it all depends on the load. So it might be that for you it works fine.
-
Thank you!! will have a look!
-
@jkandasa
Thank you for the project. I like MyController a well-developed transport layer, a lot of communication interfaces. I like using the MQTT broker. There is not enough user-friendly dashboard with drag and drop programming, so that the user does not need to delve into the subtleties of html, css, etc. to connect third-party widgets. I want a script editor with direct access to InfluxDB, so that you can make decisions on historical data, including the old one.
I do not know how to write this all at https://github.com/mycontroller-org/mycontroller/projects/1 and what open sourse resources to use. So I write the wishes in this topic.
In general, MyController cool thing! -
I think I might suggest that you forget about the dashboards, graphs and gauges, and focus on the data-flow, conversions, notifications and rules.
And dont be fooled by the time it takes to start from scratch. I dont think your timing is right, I dont see any benefits of changing all those frameworks. But a significant re-design of some parts might be cool.
-
@njbuch
You are right! I am not going to start from scratch. I will start 2.x branch from the existing code and do major changes, like support ACK (needs a lot of change on message queue), Rul engine performance improvement, Switch to Angular4 on UI, standardize REST API, ionic mobile application, InfluxDB for metrics(no more RDBMS metrics support) and much more.I have rewritten everything. Reasons:
- needs to write everything on GoLang (backend), ReactJS (frontend)
- However I have taken the logic used in 1.x, So it speeds up the development
-
The one thing I can say would be nice (from a very early user) is less reliance one scripting based setup.
While I don't mind delving into it, the ability for my non-programming-centric wife to be able to edit the schedule for our watering system would be nice.
There is a button to change the state of my relays, why do I have to script a timer for them?
set the run time in the operation for each zone, set the schedule using the timer, run.
Hope to discuss more with you all as I learn more myself!
-
@zachflem Thank you for your idea. Could you please elaborate a bit more on this? Do you want to implement readymade widget kind of things to replace script?
-
@jkandasa I like the scripting ability, don't get me wrong.
But...
I've got switches setup on the dashboard for 2 relays. It would be nice to add a feature to those switches to automatically turn them off after x seconds/minutes.
or
As part of the operations tab, have the option to select the sensor (in this case a relay) and set the status to "ON" and the duration to x seconds/minutes. Then setting a reoccuring timer to run, using that operation would result in the sensor (the relay) operating for the defined duration.
I might not be explaining myself very well, I'd just like to see some scheduling into the GUI so my wife could change/setup a new watering schedule if I'm not around.
A little off topic, but is there any documentation about scripting in mycontroller?
